Piano World Home Page Forums Our Most Popular Forums Piano Tuner-Technicians Forum How Can You Describe The Sound Of Strings Needing Leveling??

I have read technicians comment that "It sounds like the strings need leveling."

How would you describe this sound?

tuuuurrrriiiinnnggg

It sounds "out of phase" instead of out of tune. I notice it most while tuning unisons - there is no place where the unison if really pure, but there are no false beats on single strings to explain it.

What happens usually is 2 or 3 strings are sitting at the bar. One of the strings states “I’m just not feeling 100% these days. One of the other strings states” are you on the level?”

Nick, I think it is a common mistake made on forums...it should actually state “this reads like the strings need levelling.”

Whew! I am glad that Dan didn't notice I spelled "tuuuurrrriiiinnnggg" wrong. (Now what was that silly rule about triple vowels and quadruple consonants???)

Nick, there is always a high partial that is prominent. The first reaction is to use a needle to suppress it but that is going after the symptom rather than the cause. The wrong solution can often leave the note sounding dull but still leave the annoying high partial.

It is actually a very simple concept. You know how you can get a high partial to sound by lightly touching a string in a certain spot? This can be done on a piano but guitarists often do it both in playing and tuning. When one piano string is higher than the other two, it is not struck with the same force as the other two or not even struck at all, just lightly brushed. That induces the high partial sound to be prominent. It is often described as a "whine" , "sizzle", "buzz" or a "ping".

It can sound similar to what a hard spot on a hammer would produce. Generally, the harder and brighter sounding the hammers are, the more of a problem string leveling becomes.

Welcome back Bill.....perfect explanation....
Anyone out there know why this piano 101 procedure is such a mystery to many techs when its application is so crucial to focus and tone.

Thanks Bill,

Do you think it could be described also as sort of a whistling sound, kind of raspy, like there is air mixed in with the tone, a hissing sound, if that makes any sense? Sounds sort of related to strings needing seating? Peter?

Snotty.

Yes, that would describe it too. Kieth's description is funny as i have also heard it described as "nasal".

Everyone's word for it may vary but it all has to do with a high partial (or maybe more than one) that is overly prominent.

Not all manufacturers advocate string leveling, so having level strings isn't the overall goal. Having hammers which are fitted to the strings is the goal. Leveling strings is one step in that process. I like doing it, because I think it makes the process of fitting hammers to strings more efficient. It also means that the hammers still fit the strings when the keyboard is in the shift position.

I just wanted to point out that string leveling alone doesn't eliminate the "out of phase" sound. Some techs like to fit the hammers to the strings instead.

Yes, strings needing seated is a similar sound.

It's a matter of perception and priorities, Peter. Cheap grands have a low profit margin. The dealer doesn't want to pay a highly skilled technician for hours of work on something someone would buy whether voicing was done or not. There is always the assumption that the hammers will even themselves out eventually anyway.

I don't view it as such a basic skill either. It takes time and expertise to learn to do that well and efficiently.

What is the best way to hold the hammer when checking string mating, i.e. how does one best hold the hammer so that it barely touches, to see whether the (plucked) strings are all equally damped by the hammer? I have found that even the slightest force on the hammer damps all three strings, so my challenge is to find a grip on the hammer that exerts practically zero force on the strings, yet is sturdy and consistent enough to test all three strings one after the other. Any advice?

Mark:

What I do is play the note and then damp it by using the hammer itself. If they all stop at the same time, fine. If one keeps ringing, figure out which one by damping with a mute or something.

Hi Mark:
There are two basic methods that I see used. One is to put a layer of felt between the repetition lever and the knuckle. Then you push up from the bottom of the wippen to raise the hammer up to the strings. Normally the letoff function won't let you do this, and the hammer will fall away. The layer of felt provides a spacer which lets the hammer rise all the way to the string.

The other method is to reach down between the strings with a hook. They are often made out of music wire, with some sort of wooden handle attached. These can easily be home made. The hammer is then lifted up to the string by the shank.

Jeff and Roy,

Thanks for the useful tips. BTW, Roy, I'm not a tech; I only work on my own pianos, but nevertheless want to check this on my upright (two uprights, in fact), as part of working through the whole regulation process according to Arthur Reblitz. So, to translate your suggestion from grand to upright: I could try a piece of felt between the jack and the butt.

Sorry Mark, didn't realize you were talking about a vertical. There the hammers are accessible, so you can just press them forward with your hand. I haven't tried using felt on a vertical, so I can't say.

Well, yes... but as I wrote initially, I have the problem that my grip on the hammer is not fine or consistent enough: I seem to have problems with
a) bringing the hammer to the strings up to a point where it just barely touches but exerts no force, and then
b) keeping it perfectly still in that exact position while I test all three strings.

If I grip the hammer close to the head, I exert too much force and all the strings are damped immediately. If I grip it closer to the butt, I have too little control over the exact position. (Almost like the Heisenberg Uncertainty Principle...)

I'll try Jeff's idea of playing the note and then muting it using the hammer - hoping that I'll hear the difference between the decay sound of three strings and one string.

On an upright...
Using your left hand push the hammer to the string using middle finger and then lift the rep lever using your thumb on the backcheck.
This will prevent you from needing to depress the pedal and will also give less 'noise' as only one note will be 'open'...
Does that make sense??

I find the use of a little metal ruler pushing on the shank to be more precise than a nail at the back of the head.

a little flat rule on the strings also may show something.

Umm, Peter, rep lever? On an upright? If by "rep lever" you mean damper or perhaps wippen, then I think I catch your drift: presumably you ensure that the damper is off the string by lifting the wippen by the backcheck.

Isaac: ah, a ruler, good idea - thanks. (Good to see you back in the forum)